If your dishwasher finishes a cycle with cold, wet dishes—or the detergent hasn’t dissolved properly—the heating element may be the cause. A multimeter can help you check it, but the test only tells you what’s happening if the dishwasher is safely disconnected from power and you measure the element correctly. Here’s how to do that, what the readings mean, and what to check before you buy a replacement.
Table of Contents
What the dishwasher heating element does
The heating element warms the water during parts of the wash cycle and may also help dry dishes. On some dishwashers, it’s the visible loop at the bottom of the tub. On others, it’s hidden inside a circulation or heating assembly, so you may not see a traditional exposed coil.
A broken element can leave dishes cool or damp, but those symptoms don’t prove the element has failed. The dishwasher may also have a wiring problem, a faulty temperature sensor, a control issue, or a cycle setting that doesn’t use heated drying. Testing the element helps narrow down the cause.
Safety comes first
A dishwasher combines electricity, water, and metal parts. Never check resistance or continuity while the appliance is connected to power. A meter’s ohms and continuity modes are designed for an unpowered circuit; using them on a live circuit can damage the meter and expose you to a serious shock hazard.
- Switch off the dishwasher’s circuit breaker. Don’t rely only on the control panel or a wall switch.
- Make sure the power is off. If you can safely access the wiring area, use a properly rated voltage tester to verify there’s no power before touching wires. If you’re unsure how to do this, stop and call an appliance technician.
- Keep the area dry. Mop up standing water and don’t handle electrical parts with wet hands.
- Don’t test the element while the dishwasher is running. Live-voltage testing is a different procedure and is best left to someone qualified to work safely around energized appliances.
Check your dishwasher’s manual or service information before removing panels. Models vary, and opening the wrong panel can damage clips, seals, wiring, or insulation.
What you’ll need
- A digital multimeter with resistance and continuity settings
- A screwdriver or nut driver suited to your dishwasher’s fasteners
- Work gloves and a flashlight
- The dishwasher’s manual or model number, if available
A multimeter measures electrical resistance in ohms, shown by the symbol Ω. Continuity mode is a quick way to see whether there’s an unbroken electrical path. Resistance mode gives you a more useful numerical reading, which you can compare with the expected value for that element.
How to test a dishwasher heating element
1. Turn off the power and prepare the dishwasher
Switch off the dishwasher’s breaker. If the dishwasher is hardwired, don’t try to disconnect its electrical supply unless you’re trained to do so. Confirm that power is off before you access any wiring, and let the appliance cool if it was recently used.
If you need to work near the bottom of the tub, remove dishes and the lower rack. Some models require access from underneath the dishwasher, which may mean removing a toe-kick panel or pulling the appliance out. Don’t tug on the dishwasher or its hoses and wiring; get help or contact a technician if the access is difficult.
2. Find the heating element and its terminals
On a dishwasher with an exposed element, look for the metal loop running along the floor of the tub. The electrical terminals often pass through the tub floor and connect to wires underneath. A dishwasher with a hidden heater may instead have a heating assembly connected to the circulation pump.
Use the manual or model-specific service information to identify the correct part. If you can’t confidently tell which component is the heater, don’t guess. Testing the wrong terminals can give you a meaningless reading or lead you to disconnect an unrelated safety component.
3. Disconnect at least one wire from the element
Take a clear photo of the connections before you remove anything. Then disconnect at least one wire from a heating-element terminal, pulling on the connector rather than the wire itself.
This matters because the element is connected to other parts of the dishwasher’s electrical circuit. If you leave both wires attached, the meter may send its tiny test current through another path and show a reading that doesn’t belong to the element alone. Disconnecting one wire helps isolate the component.
4. Set the multimeter to resistance
Put the black probe in the meter’s COM port and the red probe in the port marked for volts, ohms, or both. Select resistance mode, shown as Ω. If your meter has manual ranges, choose a low range such as 200 Ω. If it selects the range automatically, just choose Ω.
Touch the probe tips together first. The meter should show a very low value, often close to zero, or beep if you use continuity mode. This quick check confirms the probes and meter are responding.
5. Measure across the two element terminals
Touch one probe to each of the element’s two electrical terminals. Keep the probe tips on the metal terminals, not on the disconnected wires. Read the display and compare it with the expected resistance in the dishwasher’s service information.
| Meter result | What it may mean | What to do next |
|---|---|---|
| A stable resistance reading | The element has a continuous electrical path. That doesn’t prove every part of it works under operating conditions. | Compare the reading with the manufacturer’s specification and check other parts of the heating circuit if the dishwasher still won’t heat. |
| OL, infinity, or no continuity | The circuit through the element appears open, which often means the element has failed. | Confirm you tested the correct terminals and that at least one wire was disconnected. Then check the model’s service information. |
| A reading close to zero | The element may be shorted, or the probes may be touching the same terminal or another connected path. | Repeat the test with the element isolated and make sure each probe touches a different terminal. |
| A value that jumps around | The probe contact may be poor, a connector may be loose, or the component may not be fully isolated. | Check the terminals, probe contact, and wire connections, then test again. |
What resistance should a dishwasher element have?
There isn’t one correct reading for every dishwasher. The expected resistance depends on the element’s rated voltage and power. If you know those ratings, you can estimate resistance with this formula: resistance in ohms = voltage squared ÷ power in watts.
For example, a 1,200-watt element designed for a 120-volt supply has an estimated resistance of 120 × 120 ÷ 1,200, or about 12 ohms. A 1,500-watt element at the same voltage works out to about 9.6 ohms. These are examples, not universal specifications; use the value provided for your exact dishwasher whenever you can.
A reading that’s reasonably close to the specified value suggests the element isn’t completely open or shorted. But a normal resistance reading does not guarantee the heater works perfectly in every condition. A damaged element can sometimes fail only when hot, and a regular multimeter resistance test may not reveal insulation leakage that appears during operation.
Check for a short to the element’s metal body
With the dishwasher still disconnected from power and at least one element wire removed, you can do a basic check for an obvious short. Touch one probe to an element terminal and the other to the element’s metal sheath or another exposed, unpainted metal part of the element. Repeat on the other terminal.
On a typical isolated element, the meter should show OL or no continuity between either terminal and the metal body. A measurable path can indicate that the element is leaking current to ground and may need replacement. Don’t touch the probes to painted, coated, or dirty areas and assume the result is reliable; poor contact can make the reading misleading.
This is only a basic screening test. A standard multimeter can miss insulation breakdown that shows up only when the element heats or when tested at higher voltage. A technician may use an insulation-resistance tester for a more thorough check. Don’t try to reproduce that test by powering the dishwasher with exposed wiring.
If the element tests okay, what else could be wrong?
If the resistance is within the manufacturer’s range, the heater may not be the problem. Heating depends on a chain of parts and conditions: the dishwasher must have enough water, the control system must call for heat, and the wiring and safety devices must allow current to reach the element.
- Loose, burned, or damaged wiring: A good element can’t heat if a connector or wire is broken. Look for melted insulation, corrosion, or loose connections, but don’t handle wiring until power is verified off.
- Temperature sensor or thermostat: These parts help the dishwasher track or limit water temperature. A faulty sensor can prevent heating or cause the cycle to behave unexpectedly.
- Control board or heater relay: The control may fail to send power to the heater. Diagnosing that often requires model-specific procedures, and some checks involve live voltage, so a technician is the safer choice.
- Low water level or circulation trouble: If water isn’t reaching the expected level or circulating properly, heating may be delayed or prevented. A blocked filter or spray arm can also make cleaning poor even when the element works.
- Cycle settings: Some energy-saving or air-dry settings use less heat or no heated drying. Check the selected cycle before assuming a part has failed.
Also check whether the dishwasher displays an error code. Write it down before resetting the appliance, then look it up in the manual for your exact model. An error code can point toward a heating problem, though it doesn’t automatically prove the element itself is faulty.
Should you replace the element yourself?
If the element clearly fails its resistance test and the replacement procedure is straightforward for your model, a confident DIYer may be able to replace it. Order the part by the full model number, not just by the dishwasher’s brand. Similar-looking elements can have different terminal shapes, wattages, or mounting arrangements.
Before fitting a replacement, check its gasket or seals, connectors, and mounting points. Follow the manufacturer’s instructions and reconnect every wire to the correct terminal. If access requires moving a hardwired dishwasher, disconnecting plumbing, or working in a cramped space near wiring, bringing in a qualified appliance technician is a sensible choice.
After any repair, reinstall panels and covers before restoring power. Watch for leaks during the next cycle, and stop the dishwasher if you notice water near electrical parts, a burning smell, or repeated breaker trips.
Read more related posts:
- how do you maintain a gutter downspout years to come?
- How to stop pipes from banging good
- How to unclog a sink drain Without Harsh Chemicals
Frequently Asked Questions
Can I test a dishwasher heating element without removing it?
Often, yes. You can test it in place if you can safely reach its terminals, disconnect at least one wire, and keep the dishwasher disconnected from power. If the terminals are inaccessible or the heater is part of a hidden assembly, follow the model’s service instructions or call a technician.
What does OL mean on a multimeter?
OL usually means “over limit” or an open circuit. Across the two isolated element terminals, it suggests there may be no continuous path through the heater. Confirm the meter is in resistance mode, the probes are making contact, and you’ve identified the correct terminals.
Will a continuity beep prove the heating element is good?
No. A beep only suggests there’s some electrical path through the component. The resistance could still be outside the dishwasher’s specification, and a basic continuity test won’t reliably detect every insulation problem or failure that happens only when hot.
Can I test the dishwasher heater while it’s running?
Don’t do this unless you’re qualified to perform live electrical testing. The dishwasher contains exposed electrical connections and water, creating a serious shock risk. Use an unpowered resistance test for a basic check, or have a technician diagnose the live circuit safely.
Conclusion
To test a dishwasher heating element with a multimeter, disconnect power, identify the correct heater terminals, remove at least one wire, and measure resistance across the element. Compare the result with the specification for your model rather than relying on a single number. A failed reading can point to a bad element, but a normal reading doesn’t rule out wiring, sensor, water-level, or control problems. If you can’t verify the power is off or safely access the part, stop and get professional help.