Product reviewHeating & Cooling

Best Hot Tap Water Heater: Faucet and Under-Sink Options Compared

Updated 10 min read

Reader-supported: when you buy through links on our site, we may earn an affiliate commission at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases. Learn more.

A hot tap water heater can give you warm water at a sink without heating and storing a full tank. The right choice depends on whether you want an all-in-one faucet or a compact heater installed near an existing faucet—and whether your wiring can support the unit. These five options range from simple heating faucets to dedicated under-sink heaters, so compare their installation needs and output before you buy.

Quick Comparison

ProductType and powerStandout featureBest suited for
EHERDM 110V Instant Tankless Electric Water Heater FaucetHeating faucet, 110VLED display and 360-degree rotating spoutA sink that needs a compact, integrated hot-water tap
lyrlody 3000W Water Heater FaucetHeating faucet, 3000WDigital display and rotating spoutShoppers who can confirm availability and electrical details
ThermoMate 3500W On-Demand Water HeaterUnder- or over-sink heater, 120VAdjustable digital temperature controlA small sink with compatible dedicated wiring
Fabater 110V 3000W Hot Water Heater FaucetHeating faucet, 110VLED display and 360-degree rotationA kitchen or bathroom sink where an integrated tap is preferred
Rheem 3.5kW Point-of-Use Tankless Water HeaterPoint-of-use heater, 120VThermostatic controls and stated maximum flow of 0.5 GPMOne fixture, such as a basement sink or garage workshop

Our Picks: Best Hot Tap Water Heater reviews

1. EHERDM 110V Faucet: An All-in-One Tap with a Temperature Display

The EHERDM combines a faucet and an on-demand electric heater in one unit. It heats water as it flows through the tap, so it does not require a separate storage tank. The LED display shows the water temperature, and the spout rotates 360 degrees to make it easier to direct the stream around a sink.

The listed “big under bend” design measures about 6.69 by 15.75 inches and weighs about 0.9 kg. Its shell is ABS engineering plastic, with an aluminum-alloy handle and stainless-steel water inlet. Check the spout shape, available space, water connection, and electrical setup against your sink before ordering.

The supplied information gives a winter water-temperature range of about 86–104°F. That makes this a better fit for everyday sink tasks than for anyone expecting a high-volume supply of very hot water. As with other heating faucets, the water’s temperature depends on the installation and how the unit is used.

Pros:

  • Combines the faucet and heater in one compact unit.
  • LED display makes the water temperature easier to monitor.
  • Rotating spout offers flexible sink coverage.
  • Listed dimensions and materials help with basic fit planning.

Cons:

  • Requires installation and a compatible electrical and water setup.
  • The stated winter temperature range may not meet every hot-water need.

Verdict: Choose the EHERDM if you want an integrated, rotating hot-water faucet for a compatible sink and can work within its stated temperature range.

2. lyrlody 3000W Faucet: A Rotating Tap with a Digital Readout

This lyrlody model is an electric heating faucet rated at 3000W. Its listed features include a digital temperature display and a 360-degree rotating water pipe. The product description says it heats water in three to five seconds and gives a temperature range of 30–60°C, but the actual result will depend on conditions such as incoming water and flow.

The listing describes a stainless-steel body and presents the faucet as a direct heating tap. However, the supplied product details do not state its operating voltage or provide enough installation information to confirm electrical compatibility. Those details matter for an appliance that heats water at the sink, so verify them with the seller or product documentation before considering installation.

The supplied listing information also marks this product as unavailable. That can change, but it makes this a less straightforward choice than the other options. It is worth comparing only if it becomes available and you can confirm the specifications that are missing.

Pros:

  • Listed 3000W heating power and a digital temperature display.
  • Rotating spout can help direct water around the sink.
  • Stainless-steel body is specified in the product description.

Cons:

  • The supplied information does not state the operating voltage.
  • The product is marked unavailable in the supplied listing data.

Verdict: Consider this faucet only after confirming that it is available and getting clear voltage and installation specifications.

3. ThermoMate 3500W Heater: Adjustable On-Demand Water for a Small Sink

Unlike an all-in-one heating faucet, the ThermoMate is a separate compact heater designed for installation under or over a sink. Its stated size is 7.9 by 6.4 by 2.5 inches, and it connects to a faucet through its water fittings. A touch control panel and digital display let you set the temperature from 86°F to 131°F in one-degree increments.

The unit is rated at 3500W and 120V, with a listed flow range of 0.4–0.66 GPM. Its description says the heater adjusts power as inlet flow and temperature change. It also specifies a cast-aluminum heating element separated from the water line and a stainless-steel water tube.

Electrical requirements deserve special attention: the supplied details say the unit must be hardwired, has no plug, and requires a 32A double-pole circuit breaker and at least 10 AWG wire. Have a qualified electrician check the circuit and installation plan before buying. This model may suit a small sink where its output and wiring requirements match, but it is not a casual plug-in upgrade.

Pros:

  • Compact form is intended to fit beneath or above a sink.
  • Digital controls offer a stated 86–131°F setting range.
  • Provides a separate heater rather than replacing the faucet.
  • Product details specify its flow range and electrical requirements.

Cons:

  • Must be hardwired and requires a suitable dedicated circuit.
  • Its flow range is intended for point-of-use use, not whole-home demand.

Verdict: Pick the ThermoMate if you need a compact heater for one sink and an electrician confirms that your wiring meets its stated requirements.

4. Fabater 110V Faucet: A 3000W Tap with Splash-Resistant Design

The Fabater is another integrated electric heating faucet. It is listed as a 110V, 3000W model, with an LED display for the water temperature and a spout that rotates 360 degrees. The product description gives different temperature ranges for winter and summer—about 30–40°C in winter and 30–60°C in summer—and notes that flow affects the result.

The description specifies a stainless-steel body and an IPX4 rating, which it characterizes as splash-proof. That rating does not remove the need to follow the installation instructions or keep electrical connections protected. The product information also emphasizes the correct sequence: turn on the water before switching on the electricity.

Compared with the EHERDM, the Fabater has a higher stated heating wattage and a described seasonal temperature range, but the supplied details do not include dimensions or a full set of electrical installation requirements. Confirm the mounting fit and circuit needs before purchase. Like other heating faucets, it is most appropriate for a single compatible sink rather than a whole-home hot-water supply.

Pros:

  • Integrated faucet and heater with a 360-degree rotating spout.
  • LED display shows water temperature.
  • Listed as 110V and 3000W, with an IPX4 rating in the product description.
  • Seasonal temperature ranges are provided, with a note that flow affects output.

Cons:

  • Dimensions and complete circuit requirements are not included in the supplied details.
  • Installation must follow the stated water-first, electricity-second sequence.

Verdict: The Fabater is worth considering if you want a rotating 110V heating faucet, provided you confirm its fit and electrical requirements before installation.

5. Rheem 3.5kW Heater: A Point-of-Use Option from an Established Brand

The Rheem RTEX-04T is a separate point-of-use heater, not a replacement faucet. Its 3.5kW, 120V design is intended for one fixture, with examples including a basement sink, garage workshop, or outdoor kitchen. The stated maximum flow is up to 0.5 GPM, so it is best considered for a limited sink application rather than several fixtures at once.

Its digital thermostatic controls adjust in one-degree increments across a stated range of 80°F to 140°F. The product details list a 30-amp single-pole breaker, #10 AWG copper conductors with ground, and a recommended minimum 100-amp household electrical service panel. These requirements should be checked against your home’s wiring and local rules before purchase.

Rheem lists a five-year leak warranty and a one-year parts warranty. A separate heater can suit you if you want to keep your existing faucet, but it needs a suitable installation location and compatible plumbing connections. It also has more specific electrical requirements than a simple faucet swap, so professional installation may be the sensible route.

Pros:

  • Thermostatic controls provide a stated setting range of 80°F to 140°F.
  • Designed for a single point-of-use fixture.
  • Electrical requirements and warranty terms are specified.
  • Compact tankless format does not store a full tank of water.

Cons:

  • Listed maximum flow of 0.5 GPM limits its intended use.
  • Requires wiring and a circuit that meet the stated specifications.

Verdict: Choose the Rheem for a single sink when you prefer a separate point-of-use heater and its electrical requirements fit your home.

How to Choose a Hot Tap Water Heater

Decide Between a Heating Faucet and a Separate Heater

A heating faucet combines the tap and heater, which can be useful if you are replacing a faucet or setting up a sink that needs its own hot-water source. A point-of-use heater, such as the ThermoMate or Rheem, is a separate unit installed near a faucet. It may let you keep your existing tap, but you need room for the heater and compatible plumbing connections. Check the product’s installation instructions to see which setup matches your sink.

Check Voltage, Wattage, and Circuit Requirements

Do not choose a heater based on voltage alone. Confirm its wattage, required breaker, wire size, and whether it needs hardwiring. The products here have different electrical specifications: for example, the ThermoMate lists a 32A double-pole breaker, while the Rheem lists a 30-amp single-pole breaker. These are not interchangeable requirements. Ask a qualified electrician to confirm your circuit can safely support the unit and follow local electrical rules.

Set Realistic Expectations for Temperature and Flow

On-demand heaters warm water as it flows, but the temperature you get depends on the incoming water, the flow rate, and the heater’s capacity. A product’s stated temperature range is not a promise of the same output in every home or season. Check both the temperature information and any flow-rate specification. For example, the Rheem lists a maximum flow of up to 0.5 GPM, while the ThermoMate lists a range of 0.4–0.66 GPM.

Measure the Sink and Installation Area

For a heating faucet, check the faucet opening, sink depth, spout shape, and room for the handle to move. For an under-sink heater, measure the available cabinet space and check where its water connections and electrical supply will go. The EHERDM provides listed dimensions, while the ThermoMate lists a compact 7.9-by-6.4-by-2.5-inch body. Do not assume that similar-looking products have the same fit.

Review Installation and Water-Safety Instructions

Water and electricity require careful installation. Follow the manufacturer’s instructions for water connections, grounding, circuit protection, and startup. The Fabater description specifically says to turn on the water before the electricity. If you are unsure about plumbing or wiring, use a qualified professional rather than guessing or modifying the unit.

Look at Warranty and Support Details

Warranty coverage can help you compare products, but check the full terms and what they cover. The Rheem listing specifies a five-year leak warranty and a one-year parts warranty. The other supplied product details do not provide comparable warranty information, so look for current manufacturer documentation before making your decision.

Frequently Asked Questions

What is a hot tap water heater?

It is a small electric water-heating product meant to provide hot or warm water at a sink. Some models are built into the faucet, while others are separate point-of-use heaters installed near a faucet.

Do these heaters provide hot water for an entire home?

The products in this guide are designed for a sink or one fixture, not as whole-home water heaters. Check each product’s stated flow and intended use before deciding whether it can meet your needs.

Is a heating faucet the same as an under-sink heater?

No. A heating faucet combines the tap and heating function in one unit. An under-sink heater is a separate appliance connected to a faucet and water supply. Their installation and space needs differ.

Can I install one of these heaters myself?

Installation needs vary, but several models require electrical work or specific circuit requirements. Read the instructions first, and have a qualified electrician or plumber handle work that is beyond your skill or local rules.

Will an on-demand heater always produce the listed temperature?

Not necessarily. Incoming water temperature and water flow affect the output. Treat the listed range as product information, not a guarantee that every installation will deliver the same temperature.

What is the difference between the ThermoMate and Rheem models?

Both are separate point-of-use heaters, but their listed specifications differ. The ThermoMate is rated at 3500W and lists a 0.4–0.66 GPM flow range, while the Rheem is rated at 3.5kW and lists up to 0.5 GPM. Their breaker requirements also differ, so compare the installation details carefully.

Final Recommendation

For a compact all-in-one tap, the EHERDM is a straightforward option to compare because its listed details include dimensions, materials, a temperature display, and a rotating spout. If you want a separate heater for one sink, the Rheem provides clear point-of-use and electrical specifications, though its listed flow is limited. The ThermoMate is another compact choice with adjustable controls, but its hardwiring requirements make an electrical check essential. Whichever type you choose, match the heater to your sink, water needs, and home wiring before you buy.

Rate this post
Spread the love

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top