Product reviewHeating & Cooling

Best Gas Instantaneous Water Heaters: Top Picks Compared and Reviewed

Updated 11 min read

Reader-supported: when you buy through links on our site, we may earn an affiliate commission at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases. Learn more.

Gas instantaneous water heaters heat water as it flows instead of storing it in a tank, which can save space and provide a steady supply when the unit is sized for your home. The right choice depends on your incoming water temperature, how many fixtures may run at once, and whether your home can support the heater’s gas and venting needs. Our picks range from compact models for lighter use to higher-capacity options for larger households.

ProductRated flowInputStandout featureBest suited for
Rheem RTG Series 7.0 GPM7.0 GPM at a 35°F temperature rise160,000 BTU0.82 UEF; LeakGuard detectionHigher household demand
APUS 3.6 GPM Indoor3.6 GPM80,000 BTUCompact size; 2-year coverageSmall homes and lighter use
Vancepic 4.3 GPM IndoorUp to 4.3 GPM100,000 BTUFour preset modesHomes needing flexible settings
ThermoMate CZ422NGUp to 5 GPM102,000 BTUCSA certification; diagnostic displayTwo-shower demand, where sizing allows
QERPRE 4.3 GPM IndoorUp to 4.3 GPM100,000 BTUKitchen, bathtub, and seasonal modesHomes that want preset controls

Note: Flow figures are not always directly comparable. Hot-water output depends on the temperature rise needed at your home, so check each unit’s specifications and have a qualified installer confirm the right size for your demand.

Our Picks: Best Gas Instantaneous Water Heaters reviews

1. Rheem RTG Series: High Capacity for Larger Homes

The Rheem RTG Series is the highest-capacity option in this lineup. It is rated at 7.0 GPM at a 35°F temperature rise and has a maximum input of 160,000 BTU per hour. Those figures make it a strong candidate for a busy home, but your actual hot-water output will depend on how much the unit must raise the incoming water temperature.

This is an indoor, non-condensing natural gas model designed for direct venting. Its listed 0.82 Uniform Energy Factor (UEF) provides a useful efficiency comparison, though actual energy use depends on household habits and installation. The wall-mount design can free up floor space, and the digital control panel allows temperature adjustments in 1°F increments.

Safety and leak detection are notable features: the supplied specifications list freeze and flame-failure protection, a multi-point safety system, and LeakGuard detection and prevention. The unit is described as CSA certified. However, its larger capacity does not make it a simple swap for every tank heater. Check gas-line capacity, vent requirements, and local code with a qualified installer. The supplied listing also shows this model as unavailable, so confirm its current availability before planning around it.

Pros:

  • Highest stated flow and BTU input among these picks
  • Rated at 7.0 GPM at a specified 35°F temperature rise
  • Leak detection, freeze protection, and flame-failure protection are listed
  • Wall-mounted design saves floor space

Cons:

  • Its gas, venting, and electrical requirements need careful installation planning
  • The supplied listing indicates it may not currently be available

Verdict: Choose the Rheem if your home has high hot-water demand and an installer confirms it fits your gas supply and venting setup; first verify that the model is available.

2. APUS 3.6 GPM: Compact Choice for Lighter Hot-Water Demand

The APUS is a lower-input indoor model rated at 80,000 BTU and 3.6 GPM. Its description positions it for a small home, apartment, or tiny home, with enough stated capacity for lighter use across a shower and other fixtures. The listed 0.53 GPM low-flow start may help it activate when water demand is modest, though actual performance depends on the fixture and installation.

The unit has a compact wall-mounted design, a visible LED temperature display, and a stated adjustment range of 95°F to 149°F. Its specifications list a 0.81 UEF and an oxygen-free copper heat exchanger. The supplied description also claims up to 98% thermal efficiency; that is a separate figure from UEF, so compare the two only as their respective specifications describe them.

Freeze protection is listed as activating near 41°F, but the manufacturer’s supplied description also advises fully draining the unit below that temperature or during extended non-use. It uses 120V power, and the listing calls for licensed installation of gas, venting, and combustion components. A two-year coverage period is stated, but confirm the full terms before buying.

Pros:

  • Compact design for tight indoor spaces
  • Lower 80,000 BTU input suits lighter demand better than the larger picks
  • LED display and stated ±1°F temperature regulation
  • Two-year coverage is listed

Cons:

  • Its 3.6 GPM rating is the lowest in this comparison
  • Requires 120V power and professional gas and vent installation

Verdict: The APUS is worth considering for a small household with modest simultaneous hot-water needs, but choose a higher-capacity model if multiple showers or fixtures commonly run together.

3. Vancepic 4.3 GPM: Flexible Presets and Added Temperature Controls

The Vancepic combines a stated maximum flow of 4.3 GPM with a 100,000 BTU input. It is described as supporting three to four water points at once, but that number should not be treated as a guarantee for every home. Fixture flow and the temperature rise required are key to deciding whether it can keep up with your routine.

Four presets cover seasonal, kitchen, bathtub, and shower use. The listed temperature range is 95°F to 155°F, with a high-temperature lock intended to help reduce scald risk. An oxygen-free copper heat exchanger and dual heating chamber are also part of the supplied specifications.

The listed safety features include freeze protection rated to resist temperatures down to 14°F, along with overheat, dry-burn, exhaust-blockage, and low-water-pressure startup protection. These are product claims, not a substitute for following the installation manual or taking steps to protect the unit and plumbing during freezing conditions. Compared with the APUS, this model offers more stated flow and more preset modes; the Rheem and ThermoMate have higher listed maximum flow.

Pros:

  • Up to 4.3 GPM and 100,000 BTU input
  • Four presets for different household uses
  • High-temperature lock and several listed safety protections
  • Temperature range extends to 155°F

Cons:

  • The maximum flow figure does not specify a temperature rise
  • Confirm installation, venting, and freeze-protection needs before purchase

Verdict: Consider the Vancepic if you want preset controls and a mid-range capacity, but have an installer verify its output against your fixtures and local conditions.

4. ThermoMate CZ422NG: Mid-Range Capacity with CSA Certification

The ThermoMate CZ422NG is rated for up to 5 GPM with a 102,000 BTU input. Its supplied specifications say it can serve two showers at once while maintaining 105°F when the incoming water is 65°F. That condition matters: colder incoming water requires a greater temperature rise and can reduce the flow available at the selected temperature.

The unit is listed as CSA certified and includes a 3.5-inch LED display for temperature adjustment and status information such as flow, fan, and flame. The stated temperature range is 90°F to 140°F. Its compact dimensions and wall-mounted design may help save space, while the listed connections include 3/4-inch water fittings, a 1/2-inch gas inlet, and a 3-inch vent connection. Have an installer verify that those connections match your home and local requirements.

The supplied description lists a 0.81 UEF, an oxygen-free copper heat exchanger, and freeze protection that activates at 41°F. It also lists safeguards for flame-out, overheating, pipe blockage, and other conditions. A 120V power connection is required. The wind-resistance claim and other performance statements should be checked against the manufacturer’s documentation and your installation conditions.

Pros:

  • Up to 5 GPM with a 102,000 BTU input
  • CSA certification is stated in the supplied specifications
  • Diagnostic display shows operating information
  • Compact indoor design with listed freeze protection

Cons:

  • The two-shower performance example is based on 65°F incoming water
  • Requires 120V power and compatible gas and vent connections

Verdict: The ThermoMate is a balanced option if its 5 GPM rating fits your expected demand and a qualified installer confirms the stated connections and output work for your home.

5. QERPRE 4.3 GPM: Convenient Modes for Kitchen and Bath Use

This QERPRE model is listed at 100,000 BTU and up to 4.3 GPM, with a description that says it can supply two to three outlets at once. As with the other models, that is a stated maximum, not a promise of a particular number of showers under all conditions. The listing recommends against use above 2,000 feet, so elevation should be checked before you consider it.

Three operating modes are described: a seasonal setting that adjusts for changing conditions, a kitchen preset at 100°F, and a bathtub mode that lets you set a water volume and receive an alert when it is reached. A four-section burner and a self-modulating temperature system are listed as features intended to support steady output. The product description states temperature control within ±1°F, but real-world results depend on the installation and water demand.

The supplied specifications list an oxygen-free copper heat exchanger and protections for flame-out, freezing, overheating, dry burning, timeout, pipe blockage, high temperature, and excessive water pressure. The stated footprint is 22 inches high by 14 inches long by 6.5 inches wide. Its listed low-water-pressure start range is 3.6 to 110 PSI; confirm your home’s water pressure and the model’s installation requirements before ordering.

Pros:

  • Up to 4.3 GPM with 100,000 BTU input
  • Kitchen, bathtub, and seasonal modes add operating flexibility
  • Listed protections cover several operating conditions
  • Low-water-pressure startup range is specified

Cons:

  • The listing advises against use above 2,000 feet
  • Maximum flow is not tied to a stated temperature rise

Verdict: The QERPRE may suit a household that values preset kitchen and bathtub controls, provided its elevation guidance, water pressure, and capacity match your home.

How to Choose a Gas Instantaneous Water Heater

Size for temperature rise and simultaneous flow

Start with the amount of hot water your household uses at the same time, not just its daily use. Add the flow rates of fixtures likely to run together, such as a shower and kitchen tap. Then consider how much the heater must raise the incoming water temperature to reach your chosen setting. A model’s maximum GPM can fall as the required temperature rise increases. Ask an installer to size the unit using your local incoming-water temperature and actual fixture demand.

Check the gas supply and input rating

BTU input indicates the heater’s rated fuel demand, but a high number alone does not tell you whether the unit will fit your home. The gas line, meter, and other gas appliances all matter. A qualified professional should confirm that the supply can support the selected heater and that the appliance is set up for the correct fuel type. These models are listed for natural gas; do not assume that a natural gas unit is compatible with propane.

Confirm venting and indoor installation requirements

Indoor gas heaters need the correct venting and clearances for safe operation. Connection size, vent type, exhaust route, and local code can affect whether a model is suitable for your home. Review the installation manual and have a licensed professional inspect the proposed location. Do not choose a unit based on its compact size alone.

Compare efficiency figures carefully

Some models list a Uniform Energy Factor (UEF), while product descriptions may also state thermal-efficiency percentages or estimated savings. These figures are not interchangeable, and savings claims depend on how your household uses hot water and what equipment you are replacing. Use comparable efficiency measures when possible, and check the manufacturer’s documentation for the basis of any claim.

Plan for freezing conditions and power needs

Many indoor gas tankless heaters need electricity for controls, fans, or freeze-protection functions. Check the electrical requirements and what happens during a power outage. If the unit or connected pipes may be exposed to freezing temperatures, follow the manufacturer’s protection and draining instructions. Built-in freeze protection does not remove the need for a suitable installation or winter plan.

Look at controls, temperature limits, and safety features

A clear display and useful presets can make daily adjustments easier, but safety features and temperature limits deserve equal attention. Check whether the model includes a high-temperature lock, flame-failure protection, or diagnostic codes, and read the operating instructions. Set a safe water temperature for your household, especially if children or older adults use the fixtures.

Verify certification, coverage, and service details

Check the exact model’s certification, warranty or coverage terms, and availability of service support before buying. Confirm whether installation must be performed by a licensed professional to preserve coverage. Keep the installation and maintenance instructions, since required upkeep and service access can affect long-term ownership.

Frequently Asked Questions

What is a gas instantaneous water heater?

It is a tankless heater that warms water as it flows through the unit, rather than storing a tank of heated water. It can provide ongoing hot water while demand stays within the heater’s capacity.

Does “instantaneous” mean hot water reaches the tap instantly?

No. The heater warms water on demand, but hot water still has to travel through the pipes between the unit and your fixture. The wait depends on the plumbing layout and how far the tap is from the heater.

How much flow do I need?

Estimate which fixtures may run at the same time, then add their flow rates. You also need to account for the temperature rise from your incoming water temperature to your preferred hot-water setting. A plumbing or heating professional can help match those needs to a model’s output.

Can a tankless heater run two showers at once?

Possibly, but it depends on shower flow, incoming-water temperature, the target temperature, and the heater’s capacity. For example, the ThermoMate’s supplied description gives a two-shower example at 105°F with 65°F incoming water. That condition may not match your home.

Do gas tankless water heaters need electricity?

Some do. The APUS, ThermoMate, and QERPRE specifications list electrical requirements, and indoor models may use powered controls or fans. Check the manual for the exact model and plan for how it will operate during an outage.

Can I install one myself?

Gas, combustion, and venting work can create serious safety risks if done incorrectly. The APUS description specifically calls for licensed installation, and the other models also require careful attention to their installation instructions and local codes. Use a qualified professional to confirm the setup.

Will freeze protection prevent all freeze damage?

No feature should be treated as a guarantee against freeze damage. Follow the manufacturer’s instructions for the unit and pipes, including draining guidance when needed. The APUS description specifically advises draining the unit below 41°F or during extended non-use.

Final Recommendation

For a home with high hot-water demand, the Rheem RTG Series has the strongest stated capacity in this group, though its listed availability should be confirmed. For a smaller home, the APUS offers a more modest 3.6 GPM rating and a compact design. The ThermoMate is a middle-ground option with a stated 5 GPM maximum and CSA certification, while the Vancepic and QERPRE offer 4.3 GPM maximum ratings with different preset controls. Before choosing any model, have a qualified installer confirm its flow at your required temperature rise, gas supply, venting, and code compliance.

Rate this post
Spread the love

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top