How-to guidePlumbing & Water

What Does A Washing Machine Drain Pump Do How Does It Work

Updated 9 min read

Reader-supported: when you buy through links on our site, we may earn an affiliate commission at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases. Learn more.

Your washing machine can wash and rinse perfectly, then leave you with a drum full of water because one small part can’t do its job. The drain pump is that part: it moves used water out of the washer at the right point in the cycle. Knowing how it works can help you spot a drainage problem, avoid unnecessary repairs, and understand what to check before calling for help.

What Does a Washing Machine Drain Pump Do?

A washing machine drain pump removes water from the washer’s tub and sends it through the drain hose to a household drain or standpipe. It usually works after the wash and rinse stages, when the machine needs to empty dirty or soapy water before moving on.

The pump doesn’t wash clothes, supply fresh water, or wring out the laundry. Its job is to move water out of the machine. During a drain-and-spin stage, for example, the pump empties the tub while the washer’s motor spins the drum to remove more water from the clothes.

Without a working drain pump, water can remain in the tub. That may stop the washer from spinning, leave laundry soaked, or prevent the next part of the cycle from starting. Many washers won’t spin at full speed while there’s still too much water inside, partly to reduce the risk of imbalance or damage.

How Does a Washing Machine Drain Pump Work?

The drain pump is typically a small electric motor connected to an impeller, which is a rotating part with blades or vanes. When the washer’s controls call for draining, the motor turns the impeller. The spinning impeller moves water from the tub, through the pump, and into the drain hose.

Here’s the basic sequence:

  • The wash or rinse stage ends, and the washer’s controls start the drain portion of the cycle.
  • Water flows from the tub toward the pump. Depending on the washer, it may pass through a filter or debris trap first.
  • The pump motor turns the impeller, pushing the water into the drain hose.
  • The water travels through the hose and empties into the household drain.
  • Once the water level is low enough, the washer can continue to the next stage, such as spinning.

The pump doesn’t usually need to lift water all the way from the bottom of the machine to the drain by itself. The washer’s layout and the drain hose route help guide the flow, while the pump provides the force needed to move the water through the hose. The hose still has to be installed at the correct height and in the correct way for that specific washer. If it’s too low or positioned incorrectly, water may siphon out when it shouldn’t, or drainage may not work as intended.

Why the washer controls the pump

The drain pump is part of a timed and monitored cycle. The washer’s control system tells it when to drain, and the machine may use a water-level sensor to check whether the tub has emptied. If the water level doesn’t drop as expected, the washer may pause, display an error code, or refuse to spin.

The exact sequence varies by model. Some machines drain briefly at more than one point in a cycle, while others pause between draining and spinning. Your washer’s manual is the best source for what a particular button, light, or error code means.

What Parts Work With the Drain Pump?

The pump is only one part of the drainage path. A blockage or fault elsewhere can create symptoms that look like a failed pump, so it helps to understand the related parts.

PartWhat it doesHow a problem can affect draining
Drain filter or debris trapCatches items such as lint, coins, hair, and small objects before they reach the pump.A blocked filter can restrict water flow or make the pump noisy.
Drain hoseCarries water from the washer to the household drain.A kink, clog, or incorrect installation can slow or stop water flow.
Water-level sensorReports how much water is in the tub to the washer’s controls.If it gives incorrect readings, the washer may drain or spin at the wrong time.
Control board or timerDirects the washer through its cycle, including when to run the pump.A control problem can prevent the pump from receiving the signal to run.

Signs the Drain Pump May Have a Problem

A drainage symptom doesn’t automatically mean the pump itself is broken. A clogged filter or blocked hose can cause the same trouble. Still, certain clues suggest the pump or its surrounding parts deserve attention.

  • Water remains in the drum: The washer may stop with standing water after a cycle or fail to complete its final spin.
  • The machine makes an unusual sound during draining: A steady hum without much water movement can point to a jammed impeller, blockage, or pump fault. Rattling may mean a small object is caught nearby.
  • Draining is very slow: The pump may be struggling, but a restricted filter or kinked hose is also common.
  • An error code appears: Some washers display a code when they can’t drain within the expected time. Look it up in the manual rather than assuming it identifies one exact failed part.
  • A leak appears near the pump area: A loose connection, damaged hose, or worn pump seal may be responsible. Stop using the machine if water is reaching electrical parts or the floor around an outlet.

Listen for when the sound happens. A noise during draining is more relevant to the pump than a noise during filling or high-speed spinning. Even then, the sound is a clue, not a diagnosis.

What to Check Before Replacing the Pump

It’s easy to blame the pump when a washer won’t drain, but replacing it without checking for a simple obstruction can waste time and money. Start with checks that don’t require taking the machine apart.

1. Check the drain hose

Make sure the hose isn’t kinked, crushed behind the washer, or visibly blocked. Confirm that it’s installed at the height and in the position recommended in the washer’s manual. Don’t push it too far into a standpipe unless the instructions specifically call for that setup; incorrect placement can interfere with drainage.

2. Look for a filter or pump-cleaning access panel

Some washers have a user-accessible drain filter, often behind a small panel near the bottom front. Others don’t provide easy access, and the design differs between models. Check the manual before opening anything.

If your washer has a cleanable filter, expect water to come out. Unplug the machine first, place towels and a shallow tray nearby, and drain the water gradually using the small drain tube if the model has one. Then remove and clean the filter as instructed. Don’t force a stuck part or reach inside a pump opening with the washer connected to power.

3. Consider whether a small item is blocking the flow

Coins, buttons, lint, and other small objects can collect in a filter or pump area. If you hear a rattle or buzzing but little water moves, debris may be restricting the impeller. Accessing the pump may require removing panels, so use the service instructions or contact a qualified repair technician if you’re unsure.

4. Check the washer’s manual for error codes

An error code can narrow down the issue, but it doesn’t always prove the pump has failed. The code may indicate that the machine didn’t drain within a set time, which can happen because of a blockage, hose problem, pump failure, or another fault in the control system.

Can You Keep Using a Washer With a Faulty Drain Pump?

If the washer leaves water in the tub or repeatedly fails to drain, it’s best not to keep running full cycles. The machine may stop partway through, leave clothes soaking, or strain components as it tries to continue. Repeatedly restarting it usually won’t clear a mechanical blockage.

If you need to remove wet laundry, use the washer’s drain or emergency-drain instructions. Don’t pull a filter out quickly while the tub is full: water can spill across the floor. Unplug the machine before inspecting accessible parts, and keep water away from sockets and wiring. If you see burning smells, smoke, damaged wires, or a significant leak, stop using the washer and arrange professional service.

How to Help the Drain Pump Last Longer

A drain pump can often keep working for years, but it has to move whatever is in the wash water. Small objects and heavy lint can collect around the filter or impeller and make the pump work harder. A few habits can reduce avoidable trouble:

  • Check pockets for coins, keys, tissues, and other loose items before washing.
  • Use a laundry bag for small items that might slip through the drum openings.
  • Clean the drain filter at the interval recommended by the manufacturer, if your model has an accessible filter.
  • Use the recommended amount of detergent. Too much detergent can create excess suds and interfere with rinsing and draining.
  • Keep the drain hose unkinked and installed according to the manual.

These steps won’t prevent every pump failure. Motors and other parts can wear out over time. But they help reduce the chance that something simple, like a coin or clogged filter, will interrupt a cycle.

Read more related posts:

Frequently Asked Questions

Does the drain pump run during every wash cycle?

It usually runs during the parts of the cycle when the washer needs to empty water, such as after washing or rinsing. The exact number and timing of drain stages depend on the model and selected cycle.

Can a washing machine drain without a pump?

Most modern automatic washers use a pump to move water through the drain hose. A pump-free design would need a different way to empty the tub, but that isn’t how typical household washers are built.

Why is my washer humming but not draining?

A humming sound can mean the pump is receiving power but water isn’t moving properly. A blocked filter, jammed impeller, obstructed hose, or failing pump could be the cause. Unplug the washer and check only the user-accessible parts described in its manual.

How do I know whether the pump or the drain hose is blocked?

Start with the hose and any accessible filter because they’re often simpler to inspect. If both appear clear but the washer still won’t drain, the pump or another washer component may need diagnosis. Symptoms alone can’t confirm which part has failed.

Conclusion

The washing machine drain pump moves used water out of the tub and into the household drain, allowing the washer to rinse and spin as designed. It works with the filter, hose, water-level sensor, and controls, so a drainage problem doesn’t always mean the pump needs replacing.

If your washer won’t empty, check the manual, inspect the hose, and clean an accessible filter safely before assuming the pump has failed. When the problem continues, or you’re not comfortable opening the machine, a qualified technician can test the pump and the rest of the drainage system.

Rate this post
Spread the love

Sponsored

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top